Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for San Diego Homeowners
A gate that won’t open, drags on the ground, or makes a grinding sound at 6 a.m. isn’t just an annoyance – it’s a daily problem that gets worse every time you force it. Cambridge Gate Repair fixes gates across San Diego, from La Jolla hillside driveway gates to commercial slide gates in Chula Vista. We’re a gate specialist, not a generalist, led by Noel Carrera, and we diagnose what’s actually wrong before touching a wrench. Same-day service is available for most San Diego gate failures. Call (833) 589-8195 and tell us what your gate is doing.
Driveway Gate Repair
Driveway Gate Repair is what most San Diego homeowners call us for first: a gate that stops mid-cycle, sags on its hinges, or refuses to close all the way. In coastal neighborhoods like Coronado, salt air accelerates hinge and track wear, while inland areas like Lemon Grove and Spring Valley deal with dry soil shifting posts out of alignment. We repair the gate you have rather than selling you a replacement – whether that means re-welding a cracked post, replacing a burned-out operator, or re-hanging a gate that’s dragging on concrete. Typical driveway gate repair in San Diego runs $180 to $450 depending on parts and access. Every repair gets a fixed quote before we start, so you know the number up front.
Hinge and Post Correction
Sagging driveway gates rarely need replacing. Most of the time the post has shifted, the hinge has worn, or the weld has cracked. We reset posts, re-weld hinges, and get the gate swinging true again.
Operator and Track Repair
When an electric driveway gate fails, the culprit is usually the operator, the control board, or a bent track. We carry parts for LiftMaster, FAAC, BFT, and Linear operators, which means most driveway gates are running the same day we arrive.
Styles & brands we work with
Gate Welding
Gate Welding is the fix when a metal gate has cracked, split, or separated at a joint – common after a vehicle bump, years of wind load, or a rusted weld finally letting go. San Diego’s coastal humidity makes this worse in neighborhoods like Imperial Beach and La Presa, where unprotected steel corrodes faster than it does inland. Our welders repair iron, steel, and aluminum gates on-site, grinding back to clean metal and re-welding the joint correctly rather than just covering the crack. Gate welding in San Diego typically costs $150 to $500 depending on the size of the crack and the metal involved. The price is quoted and agreed before any work starts.
On-Site Crack and Break Repair
Most gate cracks can be welded in place without removing the gate. We bring mobile welding equipment to your San Diego property, so there’s no crane, no hauling, and no extra day of downtime.
Rust Repair and Reinforcement
If rust has eaten through a gate frame, welding alone won’t hold. We cut out the compromised section, weld in new steel or iron, and reinforce the surrounding area so the repair lasts.
Commercial Gate Repair
Commercial Gate Repair keeps apartment communities, HOAs, and business parks in San Diego operating without a gaping security hole at the entrance. A failed commercial slide gate doesn’t just annoy residents in National City – it leaves the property open and the access control system pointless. Cambridge Gate Repair handles the full chain: the physical gate, the electric operator, loop detectors, safety sensors, and access control integration. Commercial gate repair in San Diego typically runs $400 to $1,200 depending on the system and the failure. This is not the place for a handyman with a socket set. Our technicians are trained on Viking, DoorKing, and Elite commercial operators, among others.
Slide Gate and Cantilever Systems
Commercial slide gates fail at the rollers, the rack, or the motor. We diagnose which one it is before ordering parts, so your gate is back in service quickly instead of waiting on the wrong fix.
Loop Detector and Safety Edge Repair
A gate that won’t close or reverses unpredictably usually has a failed loop detector or a cut safety edge. We test and replace these components on-site, and we don’t bypass safety features to get the gate moving.
Iron Gate Repair
Iron Gate Repair covers the structural and cosmetic work on decorative iron gates, which are common on older San Diego homes in Mission Hills, Kensington, and the historic districts around La Mesa. Iron gates fail in predictable ways: rust at the bottom rail, cracked pickets, seized hinges, and broken latch hardware. We repair the actual problem – welding cracks, replacing pickets, freeing hinges, and treating rust – rather than slapping paint over it. Iron gate repair in San Diego runs $200 to $600 for typical work. If the gate is original to a historic home, we can match the existing design rather than installing a modern replacement that looks wrong.
Picket and Scroll Replacement
When individual pickets or decorative scrollwork break, the gate doesn’t need to be scrapped. We fabricate and weld in matching sections, preserving the original look of the gate.
Structural Rust Treatment
Surface rust needs to be ground back, treated, and primed before painting, or it’ll be back in a year. We handle that correctly so the repair lasts in San Diego’s coastal air.
Sliding Gate Repair
Sliding Gate Repair is about the rollers, tracks, racks, and motors that move a gate horizontally instead of swinging it. Most sliding gate failures in San Diego come down to three things: worn rollers, a bent or debris-packed track, or a motor that’s burned out from fighting a misaligned gate. We see it constantly in commercial properties and larger residential lots from Bonita to La Presa. Sliding gate repair in San Diego typically costs $250 to $800 depending on whether it’s a roller replacement or a full motor swap. The important thing is that we fix the underlying alignment issue so the new parts don’t fail the same way.
Roller and Track Realignment
A sliding gate dragging or jumping off its track usually has worn rollers or a track that’s shifted. We replace rollers, clean and realign track, and adjust the gate so it moves without straining.
Rack and Motor Repair
If the motor runs but the gate doesn’t move, the rack gear is likely stripped or the chain has broken. We carry replacement rack sections and chain kits, and we set the motor limits correctly after repair.
Wrought Iron Gate Repair
Wrought Iron Gate Repair is a subset of iron work that focuses on hand-forged or decorative wrought-style gates, which behave differently than mass-produced steel. Real wrought iron is softer and more corrosion-resistant than modern steel, but it’s also harder to weld correctly if you don’t know the material. San Diego homes with custom wrought iron gates – common in La Jolla, Point Loma, and older Coronado properties – need a specialist who can work with the original material. Wrought iron gate repair in San Diego typically runs $250 to $700. We match both the metal and the method, so the repair doesn’t stand out as a patch job.
Traditional Join and Forge Work
Welding modern steel to old wrought iron creates a weak joint that fails quickly. We use the right filler and technique for the existing material, preserving the gate’s strength and appearance.
Decorative Element Restoration
Missing scrollwork, broken finials, and bent decorative pieces can be fabricated to match. We’ve restored enough San Diego wrought iron to know that the details matter.
Metal Gate Repair
Metal Gate Repair is the broad category that covers steel, aluminum, and powder-coated gates, including the modern aluminum driveway gates you see all over newer San Diego developments and HOAs. Aluminum gates don’t rust, but they crack at welds, bend from impacts, and the powder coating chips, which lets corrosion start underneath. Steel gates rust through if they weren’t galvanized or if the paint was never maintained. Metal gate repair in San Diego runs $200 to $700 for typical work. We repair the metal properly, then address the finish so the repair area doesn’t become the next failure point.
Aluminum Weld Repair
Aluminum welding is a different skill set than steel welding, and a bad aluminum weld looks terrible and fails under load. We weld aluminum gates cleanly, then touch up the finish.
Steel Reinforcement and Section Replacement
When a steel gate has rusted through the bottom rail or a corner, we cut out the weak section and weld in new stock. The gate keeps its original dimensions and hangs square.
Wood Gate Repair
Wood Gate Repair addresses the sagging, splitting, and rotting that come with wood gates – whether it’s a redwood driveway gate in La Jolla or a cedar side gate in National City. Wood gates fail because wood moves. It absorbs moisture, dries out, warps, and eventually splits, especially when the gate wasn’t built with the right joinery or bracing in the first place. We fix wood gates by replacing rotted sections, adding or correcting diagonal bracing, resetting hardware, and rebuilding where necessary. Wood gate repair in San Diego typically runs $180 to $500. A well-repaired wood gate should last another decade or more with basic maintenance.
Frame Rebuild and Bracing
A sagging wood gate usually means the frame has racked or the bracing runs the wrong direction. We rebuild the frame, correct the brace, and re-hang the gate so it swings without scraping.
Rotted Section Replacement
If rot is confined to the bottom rail or a stile, we replace just that piece rather than the whole gate. Cedar and redwood are both readily available in San Diego, so matching material isn’t a problem.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We work on the gate you have, not the gate a dealership wants to sell you. That means our technicians are trained on the operators and gate systems already installed across San Diego, not just one brand’s catalog.
On the electric side, we regularly service FAAC and BFT hydraulic and electromechanical operators, which show up on Italian-made gates throughout the county. We also work on Linear and Viking systems, which are common on American residential and commercial installations. Whether you have one of those or any other make, we can diagnose it and get it running.
Signs You Need a Pro Right Now
- The gate is grinding, screeching, or straining. That sound means metal is wearing against metal somewhere in the hinge, roller, or operator. Running a gate with worn parts doesn’t fix itself – it just destroys the parts around it and turns a $200 hinge repair into an $800 operator replacement.
- The gate won’t close all the way. A gate that stops a few inches short or leaves a gap at the latch is a security failure. It usually points to a limit switch problem, a bent track, or a post that’s moved. Each has a specific fix.
- You can hear the motor running but the gate doesn’t move. This is almost always a stripped rack gear, a broken chain, or a decoupled drive. The motor is fine. The drivetrain isn’t. We fix that without selling you a new operator.
- The gate reverses before fully closing or opening. This is a safety sensor or loop detector problem, and it’s a common one after rain or when a sensor gets bumped. It means the gate thinks something is in the way. We test each sensor and replace only what’s failed.
- The gate has visible cracks, rust-through, or a leaning post. Structural failures get worse, and a gate that falls over is a serious injury risk. If you can see daylight through a crack or the post is leaning more than an inch, stop using the gate and call us.
Our Process, Step by Step
- 1
You call and describe the problem. We ask specific questions: is the gate manual or electric, what brand of operator, what exactly it’s doing, and how long it’s been happening. This helps us bring the likely parts on the first trip.
- 2
We diagnose on-site. Our technician checks the structure, hinges, track, and operator with a multimeter and torque tools. We test each component rather than guessing, because misdiagnosis costs you money and time.
- 3
You get a fixed quote. Before any repair starts, you get a written price for the work and the parts. That price is what you pay – no surprise line items, no “while we were in there” additions.
- 4
We repair or rebuild what’s needed. We work from the structural to the mechanical to the electrical, testing as we go. Most single-component repairs are finished in one to three hours.
- 5
We test the full cycle and walk you through it. Your gate gets cycled multiple times, safety sensors get tested, and we show you what was wrong and what we did. You know what was fixed and how to spot trouble early next time.
How Much Does Gate Repair Cost in San Diego?
Gate Repair pricing in San Diego varies by the type of gate, the failure, and the access. A typical hinge replacement on a residential swing gate runs $180 to $350. A sliding gate roller and track repair usually lands between $250 and $600. Electric operator replacement – the motor and control board – ranges from $500 to $1,200 depending on the brand and horsepower. Welding work falls in the $150 to $500 range for most cracks and breaks. Wood gate rebuilds typically run $180 to $500 depending on how much of the frame needs replacing.
What affects the price: parts availability, whether the gate is electric or manual, how far the gate is from the driveway or street, and whether we’re repairing or replacing a component. The best way to avoid overpaying is to get a diagnosis from someone who repairs gates for a living, not someone who sells them. A free estimate from Cambridge Gate Repair includes the diagnosis, the recommendation, and a fixed price before any work begins.
Our Service Area Near San Diego
Cambridge Gate Repair runs calls throughout the San Diego metro area, including San Diego proper, Coronado, National City, Chula Vista, Lemon Grove, Bonita, La Mesa, Imperial Beach, La Presa, Spring Valley, La Jolla, and Casa de Oro-Mount Helix. Most San Diego locations see a technician the same day for emergency gate failures, and we schedule standard repairs across the county within one to three business days. If you’re not sure whether we cover your neighborhood, call and ask – if we can’t get to you quickly, we’ll say so.
Serving San Diego, CA — Our Local Coverage Area
We’re based in the San Diego area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in San Diego
Gate repair is the diagnosis and correction of any mechanical, structural, or electrical problem that keeps a gate from opening, closing, latching, or operating safely. It covers everything from replacing a worn hinge to rebuilding a rotted frame to swapping out a failed electric operator. At Cambridge Gate Repair, we handle all three types of work: manual gate repair, electric gate repair, and full gate installation. For more details, see our Complete Gate Repair Guide for San Diego Homeowners. Call (833) 589-8195 to describe what your gate is doing and get a straight answer about the fix.
Most single-component repairs – a hinge, a roller, a sensor, a control board – are completed in one to three hours on-site. Structural work like post resetting or major welding can take half a day or longer. If we need to order a specific part, we’ll tell you the expected timeline before we leave. Same-day service is available for many San Diego gate failures when you call early.
Typical gate repairs in San Diego run $150 to $500 for mechanical and welding work, with electric operator repairs ranging from $500 to $1,200. The exact price depends on the type of gate, the specific failure, and the parts involved. Every repair gets a fixed quote before work starts, and estimates are free. Call (833) 589-8195 for a precise number on your gate.
Yes. We service FAAC and BFT hydraulic and electromechanical operators, Linear and Viking electric systems, plus LiftMaster, Ghost Controls, DoorKing, Elite, and Mighty Mule. We’re brand-agnostic, which means we repair what’s installed rather than pushing a replacement. If your gate has an operator we don’t recognize on the phone, we’ll still come look.
Yes, we offer same-day emergency service for gate failures that leave a property unsecured or inaccessible, including commercial gates that are stuck open or closed. Call (833) 589-8195 as soon as you notice the problem. The earlier you call, the better the odds we can get a technician to you that day.
We stand behind our workmanship and the parts we install. The specific warranty varies by the component and the manufacturer, and we’ll spell it out on your quote before any work starts. If something we fixed fails, call us – we’ll come back and make it right.
Clear any vehicles or debris from the gate’s path, including the inside of the swing arc and the track area for sliding gates. If your gate has a keypad or access control, have the entry code ready so we can test the full cycle. And if the gate is electric, note which brand of operator you have – it’s usually printed on the motor housing. That helps us bring the right parts on the first trip.
Schedule Your Gate Repair Service in San Diego Today
A broken gate doesn’t fix itself, and every day it sits broken is another day your property is harder to secure and harder to use. Call Cambridge Gate Repair at (833) 589-8195 for a free, no-obligation estimate. We’ll diagnose the problem, give you a fixed price, and get your gate working again – usually the same day. Noel Carrera and the team are ready to take your call.
Written by Noel Carrera, Owner at Cambridge Gate Repair, serving San Diego, CA.